Your Cart

RHP BOSON VPC TTL Interface Module

RHP BOSON VPC TTL Interface Module
  • VPC - Video, Power & Communication
  • USB or TTL Communication
  • Power via USB or 5 to 26Volts DC Input
  • Reverse Polarity Protected
  • USB Video Support
    • Stream Video to PC via USB
  • 2 Composite Video Outputs
    • Available with Sync Input/Output
  • Low Profile
  • Alternate connection ports

  • : We usually have a majority of these items in stock.
    Please call or contact us for availability.

Available Options

When attaching this Interface, please use proper personal grounding (or grounding wrist strap) to prevent static damage to the module.


Video Power Communication (VPC) Transistor-Transistor Logic Interface Module

Power Protection

With the intelligent polarity sensing protection, power can be provided via the USB connection or DC Voltage using the provided 6-Pin Video/Power cable or the 7-Pin Pico Blade cable.

3 Video Output Options

Video can be viewed through either the supplied JST to USB/Video cable, JST to Bare End Lead cable or 7-Pin Pico Blade to Bare End Lead cable.

Sync Ready*

Either video output can be changed to provide Sync Input/Output, via a jumper on the back of the RHP-VPC-TTL Board.
Control is maintained over USB or 3.3V TTL signals. This makes TTL Support available for any project integration.

*Please Note: External Sync is disabled on Boson <9 Hz Cameras.

The use of external sync on these cameras is not supported because pulses cannot be correlated to a specific output frame because of the way the reduced frame rate video is created. If attempted, the camera will reject commands to begin external sync mode.

This kit includes:

  • 6-PIN JST to USB/RCA Video cable (1)
  • 6-PIN JST to Bare End Leads (1)
  • 7-PIN PICO Blade to Bare End Leads (1)
  • M1.6 6mm Screws (4)
  • M1.6 10mm Screws (4)
  • Rear Cover for VPC-TTL Board (1)
  • Allen Key (1)
  • RHP VPC-TTL-IF Board (1)
  • Quick Start Guide (1)


Power Requirements:  5 Volts DC - 26 Volts DC
Power Dissipated:  Avg. 0.84W - Max. 2W
Dimensions:  21mm x 21mm
Weight:  2.6 grams
Control:  USB 2.0 and/or 3.3V TTL (1.8V Logic Available)
Video Output:  NTSC 30Hz / PAL 25Hz
Sync Output: (if configured) Master/Slave

Input Voltage 5-26VDC - Reverse Polarity Protected
Power Dissipation <0.1W (Camera Not Included),
3.5W Max With Camera,
6W Total Fused
Video Channels 2 Analog NTSC/PAL Switchable Outputs, USB Digital Video
Control Channels USB 2.0 (Video + Control)
GPIO Channels Sync Output Available - Call for details
Interface Connector

6-Pin JST SHR-06V-S-B
7-Pin Picoblade

Size 21 x 21 x 1.6mm (w/o Connector)
21 x 21 x 6mm (w/Connector)
Weight 2.6g without camera
Mounting Holes Four M1.6 Holes
Operating Temp. Range -40°C to 80°C
Storage Temp Range -50°C to 105°C
Operational Altitude 12km (max altitude of a commercial airliner or airborne platform)
What's In The Box

Boson VPC TTL IF Module - What's in the Box

Interface Assemblies Frequently Asked Questions

The FLIR Boson requires at least one interface board to allow Power and acquire Video from it's high-density connector. 

The most popular board in our product list is the Low Profile VPC module. It allows for power input, streaming USB and composite analog video as well as controlling the cameras settings.

A complete list of accessories are available at:

For video acquisition and control you will need to use the Boson Controller GUI 3.0 available from Teledyne FLIR. 

With  the RHP Boson interface boards, you may also use the RHP Boson GUI

If the USB Sensor in the Teledyne FLIR Boson is not triggered (on startup) with the proper voltage for USB-3, it will default to USB-2.

There are three ways to correct this. 

  1. Disconnect the device from the PC and reconnect.  
  2. When powering from a PC, it is best to connect USB-3 after the computer has booted up. 
  3. In some cases, the RHP-BOS-VPC3-IF can be modified to disable the voltage protection.
    Please contact support before placing your order for this modification. 

We also recommend

RHP-BOS-VPC-IF Video Power Communication Interface Simple Integration The Low Profile Boson VPC Interface Module s..
RHP-BOS-RC-IF RC-IF Remote Control Interface for the FLIR Boson Control the Teledyne FLIR BOSON remotely with the "RC-IF" Remote Contr..
RHP-BOS-CL-SY-IF Camera Link Module Converts the Boson Camera to Camera Link and provides Sync access The RHP-BOS-CL-SY-IF Camera Li..

Recently Viewed

RHP-BOS-VPC-TTL-IF Video Power Communication (VPC) Transistor-Transistor Logic Interface Module Power Protection Wit..
FLIR Boson 640