SKU: 421-0045-00
The Photon Replicator Kit includes a Photon Replicator Board, as well as a wearsaver and rear cover, that emulates the 15-pin D-sub electrical interface to Photon 320. A "horseshoe" shaped bracket is also included that, when attached to the Tau, exactly mimics the mounting scheme of the Photon 320 camera.
The Photon Replicator Kit was designed for the Tau 320. Although the kit will work with the Tau 640, digital data cannot be passed through the wearsaver connector since more data lines are re..
$400.00
SKU: 421-0051-00
PCB Assembly
Lens Focus Tool
Tripod Mount
VPC Module
Photon Replicator Board
Locking Nut
Tau Locking Nut
Tau Quick Start Guide
USB Flash Drive
Latching Cable Assembly
Latching Connector, 30pin
Contact Pins (30ea)
1.5mm Hex Key
All-In-One Package
Everything You Need To Get Started
TAU Sold Separately
The FLIR TAU/Quark starter kit includes:
PCB Assembly - TAU/Quark Development (250-0487-00)
VPC Module - TAU/Quark, Accessory (421-0048-00)
Tripod Mount - TAU..
$999.99
SKU: 421-0039-00
The FLIR Tau VPC Module is an interface for the camera to provide power and obtain video. It also facilitates serial communication for camera command and control via the free downloadable FLIR Camera Controller GUI. USB and Video cables are included...
$200.00
SKU: 421-0046-00
The Camera Link module is an expansion board for the Tau cameras that matches the functionality of the VPC Module and adds the ability to access digital data via Camera Link connection. The Camera Link module takes CMOS-type digital data from the Tau camera and converts it to Camera Link. This module does not include a Camera Link cable, frame grabber, or capture software.The Tau Camera is powered through the mini-USB connector with a nominal draw of 250mA at 5VDC for both the camera and the acc..
$750.00
SKU: 261-1485-00
FLIR NFOV Lens Holder for the FLIR TAU 2 Thermal Cameras..
$65.00
SKU: 421-0047-00
A low-profile adapter that attaches to the Tau's 50-pin Hirose connector, furnishing a solder pad interface. Schematic included...
$117.00
SKU: 110-0142-16
FLIR SDK software for the FLIR TAU Series Cameras
The Tau Software Developer's Kit (SDK part number enables camera control using one of several programming languages including VB6, VB.net, C#, and C++ (MFC). Code examples are included to help illustrate how some of the camera control functions can be used. The FLIR Camera Controller GUI is an example of an application created using the Tau SDK...
$995.00
SKU: 421-0037-00
The Tau Focus Tool can be used to change the focus of the wide field of view (WFOV) 5.5mm, 7.5mm, 9mm, 13mm, or 19mm lenses.The focus-tool accessory, allows any FLIR TAU lens which cannot be focused by hand to be focused by engaging the appropriate slots on the lens barrel such that it can be rotated inside the lens flange. (The focus tool has been properly sized such that no vignetting results when itengages the slots on the lens barrel.) Note that lens configurations with focal length.
Note ..
$60.00
SKU: 421-0041-00
The lens locking ring is designed to mount a Tau WFOV camera into a bulkhead. The M29 x 1.0 thread on the outside of the lens mount flange is placed through the clearance hole in the bulkhead and the O-ring seals the camera to the face.
The Type 2-025 O-ring is not for sale through FLIR. This is a standard O-ring available from many suppliers...
$20.00
SKU: 421-0042-00
The lock nut tool will attach to a torque wrench for proper tightening of the lens locking ring. Torque the locking ring to 4.0 in-lbs...
$70.00
SKU: 261-1467-00
FLIR Photon Replicator Board CoverRear Cover for the FLIR Photon/Tau Series Thermal Cameras...
$205.00
SKU: RHP-BOS-VPC-IF
RHP-BOS-VPC-IF
Video Power Communication Interface
Simple Integration
The Low Profile Boson VPC Interface Module simplifies integration. Two alternate Video & Power connections on the Low Profile Boson VPC Interface Module allows for a variety of installation options.
FLIR Boson GUI Friendly
You can adjust all the parameters available on the FLIR Boson using the FLIR Boson GUI when connected to your PC via the supplied USB cable.
..
$129.95
SKU: RHP-BOS-CL-SY-IF
RHP-BOS-CL-SY-IF Camera Link Module
Converts the Boson Camera to Camera Link and provides Sync access
The RHP-BOS-CL-SY-IF Camera Link module is an expansion board for the FLIR Boson camera that can connect USB power and communication, analog video, and digital data via Camera Link connection. The Camera Link module takes CMOS-type digital data from the FLIR Boson camera and converts it to Camera Link.
Master Mode
With External Sync Master ..
$399.00
SKU: RHP-BOS-RC-IF
RHP-BOS-RC-IF
RC-IF Remote Control Interface for the FLIR Boson
Control the FLIR BOSON remotely with the "RC-IF" Remote Control Interface.
Two Composite Video Outputs allow connections to separate video devices, with no signal loss.
Integrating the Boson Thermal Camera into your UAS has never been easier.
Control the Boson Camera Remotely
The RHP-BOS-RC-IF allows you to control the Boson camera remotely using a 16 Channel S-Bus Signal or up t..
$399.00
SKU: RHP-BOS-VPC-TTL-IF
RHP-BOS-VPC-TTL-IF
Video Power Communication (VPC) Transistor-Transistor Logic Interface Module
Power Protection
With the intelligent polarity sensing protection, power can be provided via the USB connection or DC Voltage using the provided 6-Pin Video/Power cable or the 7-Pin Pico Blade cable.
3 Video Output Options
Video can be viewed through either the supplied JST to USB/Video cable, JST to Bare End Lead cable or 7-Pin Pico Blade to B..
$149.00
SKU: rhp-bos-rc-hd-if
RHP-BOS-RC-HD-IF
Integrate the FLIR Boson into your UAS.
The RHP-BOS-RC-HD-IF allows you to control the Boson camera remotely using a 16 Channel S-Bus Signal or up to 5 PWM Signals from your wireless Joystick Remote Control System. Now you can assign any available parameter on the Boson to any knob, switch or lever on your Joystick Remote Controller and adjust these camera parameters ‘on-the-fly’.
With the HD Video output, video signal can be transmitted securely through a..
$499.00
SKU: rhp-bos-tau-rb-if
RHP-BOS-TAU-RB-IF
Boson Tau Replicator Interface
The replicator board adapts the Tau 2 interfaces electronically to make them compatible to the FLIR Boson Camera. By adapting the Boson's native 80-pin Hirose connector to the 50-pin TAU 2 connector used on FLIR's Tau 2 camera accessories, it makes the FLIR Boson camera electrically pin-compatible to the same connection as the TAU 2 providing an easy way to integrate the Boson to an existing installation.
Easy Integr..
$0.00
SKU: 421-0061-00
Boson VPC Accessory
For the FLIR Boson Thermal Imaging Cameras
The Boson video/power/control (VPC) is an accessory that adapts the native high-density electrical connector to a simpler USB-C interface. The Kit includes a VPC adapter, and a USB-C to USB-A cable...
$150.00
SKU: 7332558005897
Adapter for connecting a tripod.
Physical data
Size (L × W × H)
55 × 34 × 9 mm (2.2 × 1.3 × 0.4 in.)
Color
Black
Shipping information
Packaging, type
Cardboard box
List of contents
Base support
Four screws (plus six extra)
Packaging, weight
0.112 kg (0.25 lb.)
Packaging, size
170 × 64 × 75 mm (6.7 × 2.5 × 3.0 in.)
EAN-13
7332558005897
4743254001879 (Estonia plant)..
$21.00
SKU: 261-2608-00
Boson Tripod Mount
The Tripod-mount accessory, provides a means to mount a Boson assembly (or a Boson configured with either the VPC Accessory or the
Camera Link Accessory) to a tripod via a standard 1/4-20 thread. It is designed to interface to the rear of the Boson via 4 x M1.6 screws...
$45.00