The Photon Replicator Kit includes a Photon Replicator Board, as well as a wearsaver and rear cover, that emulates the 15-pin D-sub electrical interface to Photon 320. A "horseshoe" shaped bracket is also included that, when attached to the Tau, exactly mimics the mounting scheme of the Photon 320 camera.
The Photon Replicator Kit was designed for the Tau 320. Although the kit will work with the Tau 640, digital data cannot be passed through the wearsaver connector since more data lines are re..
Lens Focus Tool
Photon Replicator Board
Tau Locking Nut
Tau Quick Start Guide
USB Flash Drive
Latching Cable Assembly
Latching Connector, 30pin
Contact Pins (30ea)
1.5mm Hex Key
Everything You Need To Get Started
TAU Sold Separately
The FLIR TAU/Quark starter kit includes:
PCB Assembly - TAU/Quark Development (250-0487-00)
VPC Module - TAU/Quark, Accessory (421-0048-00)
Tripod Mount - TAU..
The Camera Link module is an expansion board for the Tau cameras that matches the functionality of the VPC Module and adds the ability to access digital data via Camera Link connection. The Camera Link module takes CMOS-type digital data from the Tau camera and converts it to Camera Link. This module does not include a Camera Link cable, frame grabber, or capture software.The Tau Camera is powered through the mini-USB connector with a nominal draw of 250mA at 5VDC for both the camera and the acc..
FLIR Tau PCB Wearsaver with Solder PadsA low-profile adapter that attaches to the Tau's 50-pin Hirose connector, furnishing a solder pad interface. Schematic included.The Tau2 Wearsaver was designed to be an internal engineering/manufacturing calibration accessory, rather than an OEM interface. There is a Hirose mating connector on one side of the board, as shown in the picture below:
When the Wearsaver is attached to the Tau2 camera, there are no exposed connectors, just the solder pads for ..
FLIR SDK software for the FLIR TAU Series Cameras
The Tau Software Developer's Kit (SDK part number enables camera control using one of several programming languages including VB6, VB.net, C#, and C++ (MFC). Code examples are included to help illustrate how some of the camera control functions can be used. The FLIR Camera Controller GUI is an example of an application created using the Tau SDK...
This adapter allows you to convert two of the mounting points on the Tau camera to a standard 1/4" x 20 tripod mounting plate.
This adapter also works with the FLIR VUE series cameras:
FLIR VUE PRO
FLIR VUE PRO R
Adapt two of the mounting points on the Tau camera to a standard 1/4" x 20 tripod mounting plate. The tripod adapter mounts to the bottom of Tau camera using two furnished socket head screws...
The Tau Focus Tool can be used to change the focus of the wide field of view (WFOV) 5.5mm, 7.5mm, 9mm, 13mm, or 19mm lenses.The focus-tool accessory, allows any FLIR TAU lens which cannot be focused by hand to be focused by engaging the appropriate slots on the lens barrel such that it can be rotated inside the lens flange. (The focus tool has been properly sized such that no vignetting results when itengages the slots on the lens barrel.) Note that lens configurations with focal length.
The lens locking ring is designed to mount a Tau WFOV camera into a bulkhead. The M29 x 1.0 thread on the outside of the lens mount flange is placed through the clearance hole in the bulkhead and the O-ring seals the camera to the face.
The Type 2-025 O-ring is not for sale through FLIR. This is a standard O-ring available from many suppliers...
FLIR 12V 4" Blackbody Source for ALC & Supplemental FFC, offers a uniform temperature source for FLIR Tau 2 Thermal Cameras.Low cost 4-inch blackbody which provides a uniform temperature source when using FLIR's Alt Lens Cal software to field-calibrate lens-less Photon or Tau cameras with third-party lenses, or to take advantage of the Supplemental Flat Field Correction (FFC) option available in the Tau 2, Vue Pro and many other radiometric camera models.
A blackbody is an important..
The FLIR Tau VPC Module is an interface for the camera to provide power and obtain video. It also facilitates serial communication for camera command and control via the free downloadable FLIR Camera Controller GUI. USB and Video cables are included...
This expansion board adapts the Tau camera's native 50-pin Hirose connector to the 30-pin SAMTEC connector used on FLIR's Photon cameras. The replicator board makes the Tau camera electrically pin-compatible to a Photon camera.
Without a Photon Replicator Board, the input voltage range is 4.0-6.0 VDC for a Tau 320 camera, and 4.4-6.0 VDC for a Tau 640. With the Photon Replicator Board, the input voltage range is modified to 6.5-27.0 VDC.* Includes spacer and screws
This expansion board adapts ..
Controlling your thermal core is easy
Control the FLIR TAU2 and VUE remotely with our RC Interface.
Assign virtually any feature to the RC controller and change all camera options ‘on-the-fly’
Continuous Digital Zoom
Color Palette Selection
FFC (NUC) Shutter Control
Spot Meter / Temp Reading
(DDE) Digital Detail Enhancement
Contrast & Brightness
Capture Images to TAU2’s Memory
7 to 32 Volts DC Input
Reverse Polarity Prot..